熔體流動速率測定儀的自動測試方法
熔體流動速率測定儀的熔體體積zui終是由活塞桿的行程決定的,這樣,只要選定行程(一般在儀器上已設置若干規格),記錄計時數值,就可很容易得到熔體流動速率,而減少了很多的人為誤差。 使用自動測試方法,還可以測試低達零點零幾、高達上千數值的材料的熔體流動速率,這在人工測試時簡直是不可能的。
在熔體流動速率測定儀整個試驗過程中,測試人員需要將熔體通過口模內孔流下的部分按時間間隔 切割下來,這里附帶有許多人工操作的誤差因素,同時,如果流動速率很大的話,試驗人員根本來不及切割操作,而如果是很小的速率,流下一段需要花費半小時甚至更長的時間,操作者的勞動強度是很大的(思想緊張)。因此,自動的試驗方法很有必要。 自動測試有二種方法:一種是:預先設定熔體流出的體積,然后對該體積的熔體的流出時間自動記錄,這是國內外通行的做法;另一種是設定熔體流出的時間。然后檢測該段時間流出的熔體的體積??傊?,流出熔體的體積和流出時間是zui終要知道的數值,而只要知道了熔體的密度,就可以知道流出的這一段熔體的質量。我們回想一下原先的定義,就可計算出熔體流動速率MFR了:
MFR=600.m/t
將m=πr2 .L.ρ代入
MFR=600.πr2 .L.ρ/ t
式中:πr2 活塞和料筒的平均截面積0.711 cm2 ,r為料筒內孔平均半徑;
L-預先設定的活塞桿下移距離(一般為1"、1/4",即25.4mm、6.35mm)
ρ*-熔體的密度,對PE,ρPE190℃ =0.7636 g/cm 3, 對PP,ρ PP230℃ =0.7386 g/cm 3 經簡化得: MFR=F/t 式中:F-系數,參見下表:
掃一掃 微信咨詢
©2024 揚州精輝試驗機械有限公司 版權所有 備案號:蘇ICP備18016239號-3 技術支持:化工儀器網 sitemap.xml 總訪問量:313252 管理登陸
電話
微信掃一掃