關于無轉子硫化儀的工作原理和其功能特點為你詳細說明
瀏覽次數:1262更新日期:2022-04-25
無轉子硫化儀儀器工作原理是測定膠料在硫化過程中剪切模量的變化,而剪切模量與交聯密度成正比,因此測定結果反映了膠料在硫化過程中交聯程度的變化,可以測出膠料初始黏度、焦燒時間、硫化速度、正硫化時間和過硫返原性等重要參數。
無轉子硫化儀采用單片機控制,其包括:主機、測溫、控溫、數據采集處理、傳感器及電氣連鎖等部分組成。其中測、控溫電路由控溫儀、鉑電阻、加熱器組成,能自動跟蹤電網及環境溫度的變化,自動修正PID參數,達到快速、精確控溫的目的。數據采集系統及機電連鎖完成對橡膠硫化過程的力矩信號自動檢測、自動實時顯示溫度及設定值。硫化結束后,自動處理、自動計算,打印硫化曲線及工藝參數。顯示硫化時間、硫化力炬,同時具有各種聲響提示。
采用計算機控制,在計算機上設定好參數后直接控制硫化儀的試驗參數。時實顯示硫化曲線和溫度曲線,存儲試驗結果,可調出不同的試驗結果對比并以不同的顏色顯示。
無轉子硫化儀將橡膠試樣放入幾乎*密閉的模腔內,并保持在試驗溫度下,模腔有上下兩部分,其中下部分以微小的線性往復移動(擺動振蕩),振蕩使試樣產生剪切應變,測定試樣對模腔的反作用轉矩(力),此轉矩(力)的大小取決于膠料的剪切模量。
硫化試驗開始后試樣的剪切模量增大,計算機機實時顯示并記錄轉矩(力),當轉矩(力)上升到穩定值或最大值乃至返回狀態時,便得到一條轉矩(力)與時間的關系曲線,即硫化曲線的形狀與試驗的溫度和膠料的特性有關。按測定原理可分兩大類型,第一類是對膠料施加一定振幅的力,測定相應的變形量,如*硫化儀和阿克發硫化儀,另一類對膠料施加一定振幅的剪切變形,測出相應的剪切力,包括有轉子和無轉子圓盤振蕩硫化儀。按使用分類有適于海綿制品的錐形硫化儀,適于工廠質量控制的硫化儀,適于研究用微分硫化儀,適于模擬厚制品硫化過程、確定最佳硫化狀態的程序控溫硫化儀等。