硫化儀兩大部分的養護講解
瀏覽次數:1955更新日期:2020-01-14
硫化儀用于分析、測定橡膠硫化過程的焦燒時間、正硫化時間、硫化速率、粘彈性模量以及硫化平坦期等性能指標,是國家規定用于研制新產品、研究膠料配方及檢驗產品質量的檢測儀器。
硫化儀可進行制品重現性、穩定性的測試,并進行橡膠配方的設計和檢測??稍谏a(chǎn)線上進行現場檢測,掌握每批、甚至每時刻橡膠的硫化特性是否滿足制品要求。用來測定未硫化膠料的硫化特性,通過橡膠在模腔內往復振蕩,對模腔的反作用轉矩(力)得到一條轉矩與時間的硫化曲線,科學地確定硫化的時間、溫度、壓力這三大要素,它們是終決定產品質量的關鍵,也可測定混煉膠配合的物理性能。
硫化儀的養護要求介紹:
一、電氣部分
1.儀器故障時先檢查保險絲是否熔斷,如有熔斷,應先分析何種原因引起,找出原因后方可換上新保險絲。
2.當保險絲均完好時,再檢查接插件是否有松動現象。
3.檢查開關電源是否符合標稱值,即輸出應為+5V、+12V,如有異常立即關閉。
4.電路板的維修原則采用整塊調換的方法,用戶在購買硫化儀時可另購備板,保修期內嚴禁亂動,否則后果自負。
5.打印機易損件應經常更換。
6.硫化儀長期不用時必須每周加電一次,加電時間不得少于15分鐘,以保持電子元件處于正常狀態。
7.線路板、測控模塊用戶一般不用拆,有問題應及時維修。
8.切勿觸摸印刷板上的集成電路片,以免靜電擊穿。
二、機械部分
1.儀器的內外部必須保持清潔,禁止使用腐蝕性的溶液或汽油清洗儀器表面。
2.每隔一兩個星期用軟布沾機油清洗兩根導柱;每個月給軸承加油,給易磨損部位加以潤滑;若長時間不用,要在上、下模表面涂以潤滑油。
3.每次做完試驗,要清理模具型腔里的橡膠殘渣,保持模具型腔內的清潔。
4.硫化儀機內氣動聯件每工作三個月需用煤油清洗一次。
5.壓力表每半年鑒定一次。
6.油霧器應保持有油,加到2/3高度。